1203.PDF
(
42 KB
)
Pobierz
19-0372; Rev 4; 10/97
MAX845 Evaluation Kit
_______________General Description
The MAX845 evaluation kit (EV kit) is an assembled and
tested isolated 5V power supply that meets PCMCIA
height requirements. Two demonstration circuits are
provided: a 100mA circuit that uses an industry-stan-
dard 78L05 regulator, and a 40mA circuit that uses a
low-cost zener shunt regulator. Both circuits consist of
a MAX845 IC (in the µMAX package), a low-profile
transformer, a half-wave rectified voltage doubler, and
a regulator.
____________________________Features
o
Isolated Power Supply
o
Low Profile (for PCMCIA cards)
Evaluates: MAX845
______________Ordering Information
PART
MAX845EVKIT-MM
TEMP. RANGE
0°C to +70°C
BOARD TYPE
Surface Mount
____________________Component List
DESIGNATION QTY
C11-C14,
C21-C24
D11, D12
D21
R22
U11, U21
U12
T11, T21
Z21
8
2
1
1
2
1
2
1
DESCRIPTION
0.1µF ceramic 1206 capacitors
Motorola MBR0520L Schottky diodes
Series-connected dual Schottky diodes
Central Semiconductor CMPSH-3S
51Ω 1206 resistor
Maxim MAX845EUA
78L05 in surface-mount 8-pin SOIC
1:1:1 low-profile transformer
Halo TGM-010P3
5.1V, 5% zener in SOT-23
Central Semiconductor CMPZ5231B
_________________________Quick Start
The MAX845 EV kit is fully assembled and tested.
Follow the steps below to verify board operation.
Do
not turn on the power supply until all connections
are completed.
The circuit on the top half of the board
can provide up to 100mA. The circuit on the lower half
of the board can provide up to 40mA.
1) Connect a 4.5V to 5.5V supply to the pad marked
+5V IN. The power-supply ground return connects
to the GND pad.
2) Connect a voltmeter and load (if any) to the +5OUT
pad. The load ground return connects to the ISO
GND pad.
3) Turn on the power and verify that the output is 5V
±5%.
4) To evaluate shutdown, cut the trace connecting SD
to GND and connect SD to V
CC
.
______________Component Suppliers
SUPPLIER
Central
Semiconductor
Halo Electronics
Motorola
PHONE
(516) 435-1110
(415) 969-7313
(602) 244-5303
FAX
(516) 435-1824
(415) 367-7158
(602) 244-4015
________________________________________________________________
Maxim Integrated Products
1
For free samples & the latest literature: http://www.maxim-ic.com, or phone 1-800-998-8800.
For small orders, phone 408-737-7600 ext. 3468.
MAX845 Evaluation Kit
Evaluates: MAX845
ISOLATED 5V @ 100mA:
T11
HALO TGM-010P3
D11
MBR0520L
+5V
IN
OFF
8
U11
C11
0.1µF
1
SD
MAX845
D1
3
FS
6
5
N.C.
V
CC
2
G1
8
7
D2
G2
4
C12
0.1µF
IN
OUT
1
ISO
+5V
U12
78L05
ISO
GND
C14
0.1µF
GND
ON
2 3 6 7
C13
0.1µF
D12
MBR0520L
LOW PROFILE, ISOLATED 5V @ 40mA:
T21
HALO TGM-010P3
R22
51Ω
D21A
C22
0.1µF
D21B
ISO
+5V
+5V
IN
OFF
U21
C21
0.1µF
1
SD
MAX845
D1
3
FS
6
5
N.C.
V
CC
2
G1
8
7
D2
G2
4
ON
CMPSH-3S
SOT-23
Z21
5.1V
C24
0.1µF
ISO
GND
GND
C23
0.1µF
NOTE: THE TWO CIRCUITS DO NOT SHARE THE SAME GROUNDS.
Figure 1. MAX845 EV Kit Schematic
2
_______________________________________________________________________________________
MAX845 Evaluation Kit
Evaluates: MAX845
Figure 2. MAX845 EV Kit Component Placement Guide—
Component Side
Figure 3. MAX845 EV Kit PC Board Layout—Component Side
Figure 4. MAX845 EV Kit PC Board Layout—Solder Side
_______________________________________________________________________________________
3
MAX845 Evaluation Kit
Evaluates: MAX845
NOTES
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
4
_____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 1997 Maxim Integrated Products
Printed USA
is a registered trademark of Maxim Integrated Products.
Plik z chomika:
Kot_Maciek
Inne pliki z tego folderu:
0001.PDF
(10 KB)
1003.PDF
(374 KB)
1002.PDF
(139 KB)
1004.PDF
(342 KB)
1005.PDF
(170 KB)
Inne foldery tego chomika:
PDF2
PDF3
SPICE
Zgłoś jeśli
naruszono regulamin