1200.PDF
(
33 KB
)
Pobierz
MAX831 Evaluation Kit
Evaluates: MAX830–MAX833
_______________General Description
The MAX831 evaluation kit (EV kit) provides a regulated
5.0V output voltage while operating on input voltages
from 8.0V to 30V. It drives loads up to 1A with conver-
sion efficiency greater than 80%.
The MAX831 EV kit is a fully assembled and tested sur-
face-mount printed circuit board. This kit comes with a
5V-output MAX831 IC, but it can also be used to evalu-
ate the MAX833 (3.0V output), MAX832 (3.3V output),
or MAX830 (adjustable output). Additional pads are
provided on the board's solder side to accommodate
the external feedback resistors used with the MAX830.
____________________________Features
o
8V to 30V Input Voltage Range
o
5V Output Voltage
o
Up to 1A Continuous Output Current
o
140µA Shutdown Supply Current
o
8mA Quiescent Current
o
Internal Power Switch
o
Adjustable Current Limit
o
Surface-Mount Construction
____________________Component List
DESIG-
NATION
C1, C2
QTY
2
DESCRIPTION
33µF, 35V, low-ESR tantalum capacitor
Sprague 595D336X0035R2B
220µF, 10V, low-ESR tantalum capacitor
Sprague 595D227X0010R2B or
AVX TPSE227M010R0100
0.047µF ceramic capacitor
Open
10kΩ, 5% resistor
3A, 40V 1N5822 (SMT) Schottky diode
Nihon NSQ03A04
Motorola MBRS340T3
100µH, 1.3A inductor
Coilcraft D03316-104
Maxim MAX831CWE
2-pin header
Shunt
MAX831 PC board
MAX831 data sheet
o
Fully Assembled and Tested
______________Ordering Information
PART
MAX831EVKIT-SO
TEMP. RANGE
0°C to +70°C
PIN-PACKAGE
Surface Mount
C3, C4
C5
R1, R2, R3
R4
2
1
0
1
______________Component Suppliers
SUPPLIER
AVX
Coilcraft
IRC
Motorola
Murata-Erie
Nihon
Sprague
PHONE
(207) 282-5111
(708) 639-6400
(704) 264-8861
(602) 244-3576
(814) 237-1431
(805) 867-2555
(603) 224-1961
FAX
(207) 283-1941
(708) 639-1469
(704) 264-1972
(602) 244-4015
(814) 238-0480
(805) 867-2556
(603) 224-1430
D1
1
L1
U1
J1
None
None
None
1
1
1
1
1
1
1
Maxim Integrated Products
_______________________________________________________________
Call toll free 1-800-998-8800 for free samples or literature.
MAX831 Evaluation Kit
___________________Quick Reference
The MAX831 EV kit is a fully assembled and tested sur-
face-mount board. Follow the steps below to verify
board operation.
Do not turn on the power supply
until all connections are completed.
1) Connect an 8V to 30V supply to the pad marked
VIN. The ground connects to the GND pad.
2) Connect a voltmeter and load (if any) to the VOUT
pad.
3) Remove the shunt on J1 for normal operation.
4) Turn on the power and verify that the output
voltage is 5.0V.
Instructions for modifying the board for different output
voltages appear in the sections
Evaluating the MAX832
and MAX833
and
Other Output Voltages.
Table 1. Jumper J1 Functions
SHUNT
LOCATION
OFF
ON
–—
——
SHDN PIN
Floating
Connected
to GND
MAX831 OUTPUT
MAX831 Enabled,
V
OUT
= 5.0V
Shutdown Mode,
V
OUT
= 0V
Evaluates: MAX830–MAX833
Notes about Inductor Selection
The 100µH Coilcraft D03316-104 inductor that comes
mounted with the EV kit has low resistance and a medi-
um current rating (1.3A). It provides excellent perfor-
mance over the line and load ranges of the
MAX830/MAX831/MAX832/MAX833.
For additional information on inductor selection, refer to
the MAX830–MAX833 data sheet.
_______________Detailed Description
Jumper Selection
The two-pin header J1 selects the shutdown mode.
Table 1 lists the jumper selectable options.
Evaluating the MAX832 and MAX833
The MAX831 can be replaced by a MAX833 to gener-
ate a 3.0V output voltage with output current up to 1A,
or by a MAX832 to generate a 3.3V output voltage with
output current up to 1A. The only modification required
is to replace the IC.
1
V
IN
+8V to +30V
C1
33µF
35V
C2
33µF
35V
2
3
4
5
R3
OPEN
6
7
R2
OPEN
8
V
IN
V
IN
V
SW
V
SW
16
15
14
13
12
11
10
9
J1
SHDN
R4
10k
C5
0.047µF
D1
1N5822
L1
100µH
V
OUT
+5V
C3
220µF
10V
C4
220µF
10V
U1
V
IN
V
SW
MAX831
V
IN
GND
I
LIM
GND
SENSE
V
SW
GND
V
C
GND
SHUT
R1
0Ω
GND
Figure 1. MAX831 EV Kit Schematic Diagram
_______________________________________________________________________________________
2
MAX831 Evaluation Kit
Evaluates: MAX830–MAX833
Other Output Voltages
The MAX831 can be replaced with a MAX830 to gener-
ate output voltages in the 2.5V to 25V range using
external resistors. Besides replacing the IC, the only
other modifications required are to cut the trace short-
ing resistor R1, add the output-voltage-divider resistors
R1 and R2 (located on the board's solder side), and
use low-ESR output capacitors with the proper volt-
age rating.
The
Pin Description
section of the
MAX830–MAX833 data sheet gives instructions for cal-
culating the values of external feedback resistors R1
and R2.
Reducing Current Limit
To reduce the output current to below 1A, or to reduce
the peak current limit to below 1.3A, install the current-
limiting resistor, R3, onto the board's solder side. See
Note 7 in the MAX830–MAX833 data sheet for instruc-
tions on selecting the resistor value.
BOARD DIAGRAM DRAWN TO REDUCED SCALE.
BOARD DIAGRAM DRAWN TO REDUCED SCALE.
Figure 2. MAX831 EV Kit Component Placement Guide—
Component Side
Figure 3. MAX831 EV Kit Component Placement Guide—
Solder Side
BOARD DIAGRAM DRAWN TO REDUCED SCALE.
BOARD DIAGRAM DRAWN TO REDUCED SCALE.
Figure 4. PC Board Layout—Component Side
Figure 5. PC Board Layout—Solder Side
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
3
___________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 (408) 737-7600
© 1995 Maxim Integrated Products
Printed USA
is a registered trademark of Maxim Integrated Products.
Plik z chomika:
Kot_Maciek
Inne pliki z tego folderu:
0001.PDF
(10 KB)
1003.PDF
(374 KB)
1002.PDF
(139 KB)
1004.PDF
(342 KB)
1005.PDF
(170 KB)
Inne foldery tego chomika:
PDF2
PDF3
SPICE
Zgłoś jeśli
naruszono regulamin