1191.PDF
(
71 KB
)
Pobierz
19-0221; Rev 3a; 11/97
MAX796 Evaluation Kit
_______________General Description
The MAX796 evaluation kit (EV kit) is a preassembled
and tested demonstration board that generates 5V and
15V. It features a flyback transformer rather than a sim-
ple inductor, providing the extra 15V output with very lit-
tle added cost. This loosely regulated 15V output is nor-
mally post-regulated to 12V with a linear regulator such
as the MAX667, in order to generate V
PP
programming
voltages for flash memory and PCMCIA sockets. The
board comes configured to accept battery voltages
between 6.5V and 28V, but can be reconfigured for
voltages between 5.7V and 30V by reducing the expec-
tation on secondary load-current capability at low volt-
ages (60mA) and substituting MOSFETs with higher
breakdown voltage ratings.
The standard board is guaranteed to deliver at least 3A
of load current on the main output and a 120mA mini-
mum on the secondary output (V
SEC
> 13V). To modify
the load-current capability, change the sense-resistor
(R1) value and re-size the external components accord-
ing to the
Design Procedure
in the MAX796/MAX797/
MAX799 data sheet.
The main output voltage comes preset to 5.08V (nomi-
nal). To select 3.3V operation, move jumper J2 to posi-
tion 2-3. For operation in adjustable mode, install resis-
tors R4 & R5 and remove the jumper.
There is a small
PC trace jumper that shunts J2 on the board. This
default jumper must be cut apart for either
adjustable-mode or fixed 3.3V operation.
Don’t oper-
ate the circuit if a jumper or resistor divider has not
been installed, as this will damage the IC due to output
overvoltage. Be sure to change the transformer turns
ratio if the secondary feedback resistor divider is
changed.
In addition to the standard components, the EV kit has
some extra pull-up and pull-down resistors (R2–R8) to
set default logic input levels. These resistors can usual-
ly be omitted in the final design. There is also an option-
al HF noise filter on the current-sense leads (R6 and
C9) that may be needed with some transformer types. If
the main output becomes noisy when the secondary
output is heavily loaded, the noise filter should be left
installed.
The MAX796 EV kit can be used to evaluate the
MAX799 IC by replacing the IC and re-wiring the trans-
former secondary. Changes needed include connect-
ing the SECFB resistor divider to REF instead of GND,
changing the transformer, and reversing the secondary
rectifier (D3) and filter capacitor (C7) polarities.
____________________________Features
o
Battery Range: 6.5V to 28V
o
Load Capability: +3.3V at 3A
+15V at 150mA
o
Precision 2.505V Reference Output
o
Oscillator SYNC Input
o
Secondary Winding Regulation
Evaluates: MAX796/MAX799
______________Ordering Information
EV KIT
MAX796EVKIT-SO
V
OUT
+5V/+15V (dual)
BOARD TYPE
Surface Mount
_____________________MAX796 EV Kit
_________________________________________________________________Maxim Integrated Products
1
For free samples & the latest literature: http://www.maxim-ic.com, or phone 1-800-998-8800.
For small orders, phone 408-737-7600 ext. 3468.
MAX796 Evaluation Kit
Evaluates: MAX796/MAX799
____________________Component List
DESIGNATION QTY
C1, C11
2
DESCRIPTION
22µF, 35V low-ESR capacitors
AVX TPSE226M035R0300
Sprague 595D226X0035R2T
220µF, 10V low-ESR capacitors
0.075Ω max
Sprague 594D227X0010R2T
0.1µF ceramic capacitors
4.7µF, 16V tantalum capacitor
Sprague 595D475X0016A2T
0.33µF ceramic capacitor
0.01µF ceramic capacitor
22µF, 25V low-ESR capacitor
AVX TPSD226M025D0200
Sprague 595D226X0025D2T
4700pF ceramic capacitor
Leave this site empty
1A, 40V Schottky diode
Motorola MBRS140T3
Nihon EC10QS04
International Rectifier 10BQ040
100mA, 30V Schottky diode
Central Semiconductor CMPSH-3
Motorola MBR0530
1A, 100V fast-recovery diode
Nihon EC11FS1
Motorola MBRS1100T3
250mW, 18V zener diode
Central Semiconductor CMPZ5248B
Motorola MMBZ5248B
5A, 30V logic-level N-channel MOSFETs
Motorola MMSF5N03HD
International Rectifier IRF7201
Siliconix Si9410
0.020Ω sense resistor
Dale WSL-2010-R020-F
IRC LR2010-R020-F
210kΩ, 1% resistor
49.9kΩ, 1% resistor
Leave these sites open
22Ω, 5% resistor
100kΩ, 5% resistor
1MΩ, 5% resistor
Transformer (1:2.2 turns ratio)
Dale LPE-6562-A092
Transpower TTI-5870
Maxim MAX796CSE
_________________________Quick Start
1) Connect a stiff (20W or better) bench power supply
to the VIN and GND pads found at the edge of the
board.
2) Check that the jumpers are set correctly (J1
installed, J2 and J3 both set to position 1-2).
3) Turn up the input voltage to somewhere between
4.75V and 28V.
4) Verify that the main output is regulating at 5V, and
that the secondary output is at 15V or so. Normal
full-load regulation is -2.5% while keeping the main
output in tolerance. If the measured error is higher,
there may be drops in the wiring or ground.
5) Ensure that the voltmeter is sensing directly at the
output and ground pads of the PC board.
To observe normal PWM switching action, place a 1A
load on the main output and observe the switching
node (device LX pin) with an oscilloscope while varying
the input voltage. Without a load, the switching wave-
forms are intermittent and difficult to trigger on, and it
may appear that the board isn’t working.
Jumper J3 comes installed for 300kHz operation.
Component values may need to be changed if 150kHz
operation is selected; see the
Design Procedure
section
in the MAX796/MAX797/MAX799 data sheet. The oscil-
lator can be synchronized to an external clock signal by
driving the SYNC pad with a pulse train of 5V amplitude.
C2, C21
C3, C8
C4
C5
C6
C7
C9
C10
D1
2
2
1
1
1
1
1
0
1
D2
1
D3
1
Table 1. Pull-Up/Down Resistors
RESISTOR
R4, R5
R6
R7
R8
FUNCTION
Adjustable-mode resistor dividers, not
installed. V
OUT
= 2.505V (1 + R4/R5).
Current-sense noise filter resistor (optional).
100kΩ SYNC pull-up resistor, usually short-
ed out (SYNC to REF).
1MΩ SHDN pull-down resistor, usually short-
ed out (SHDN to V+).
D4
1
Q1, Q2
2
R1
R2
R3
R4, R5
R6
R7
R8
T1
U1
1
1
1
0
1
1
1
1
1
Table 2. Jumper Connections
JUMPER
J1
J2
J3
FUNCTION
On/off control. Remove to force shutdown
mode.
Output voltage select. Install in position 1-2
for 5V, 2-3 for 3.3V.
Frequency select. Install in position 1-2 for
300kHz, 2-3 for 150kHz.
See Table 2 in the MAX796/MAX797/MAX799 data sheet for
component supplier phone/fax numbers.
2 ________________________________________________________________________________________
MAX796 Evaluation Kit
Evaluates: MAX796/MAX799
C11
22µF, 35V
C8
0.1µF
J1
ON/OFF
R8
1M
TO REF
R7
100k
6
C1
22µF, 35V
V
IN
= 6.5V TO 28V
VL OUTPUT
(+5V AT 5mA)
10
V+
2
SECFB
11
VL
BST
DH
14
16
D2
C4
4.7µF
Q1
D3
C10
4700pF
R2, 210k, 1%
C7
22µF
D4
18V
+15V
AT
250mA
SHDN
LX
15
C3
0.1µF
T1
1:2.2
R3
49.9k, 1%
MAX796
DL
PGND
CSH
13
12
8
Q2
D1
R1
20mΩ
+5V
AT 3A
R4
OPEN
C2
220µF
C21
220µF
TO VL
R6
22Ω
C9
4700pF
DEFAULT
J3
5
SYNC
SS
1
GND
4
3
REF
CSL
FB
9
7
DEFAULT
J2
R5
OPEN
SYNC
C6
0.01µF
C5
0.33µF
REF OUTPUT
(+2.505V AT 100µA)
Figure 1. MAX796 EV Kit Schematic
Figure 2. MAX796 EV Kit Component Placement Guide—
Component Side
_________________________________________________________________________________________ 3
MAX796 Evaluation Kit
Evaluates: MAX796/MAX799
Figure 3. MAX796 EV Kit Component Placement Guide—
Solder Side
Figure 4. MAX796 EV Kit PC Board Layout—Component Side
Figure 5. MAX796 EV Kit PC Board Layout—Solder Side
Figure 6. MAX796 EV Kit PC Board Layout—Interior
Groundplane
4
_______________________________________________________________________________________
Plik z chomika:
Kot_Maciek
Inne pliki z tego folderu:
0001.PDF
(10 KB)
1003.PDF
(374 KB)
1002.PDF
(139 KB)
1004.PDF
(342 KB)
1005.PDF
(170 KB)
Inne foldery tego chomika:
PDF2
PDF3
SPICE
Zgłoś jeśli
naruszono regulamin