1128.PDF
(
107 KB
)
Pobierz
MAX555 Evaluation Kit
_______________General Description
The MAX555 evaluation kit (EV kit) demonstrates the
operation of the MAX555 12-bit, 300MHz DAC with
ECL-compatible data and clock inputs. By supplying
power, digital bit inputs, and a differential clock, the kit
allows for quick evaluation of the MAX555’s AC perfor-
mance. A MAX555 is included in the EV kit.
____________________________Features
o
Fast and Easy Performance Testing
o
Optimized PC Board Layout
o
SMA Connectors for All Digital Input and Output
Voltages
o
Includes 50Ω Termination Resistors
o
On-Board Voltage Reference and V
TT
Generators
Evaluates: MAX555
______________Ordering Information
PART
MAX555EVKIT
TEMP. RANGE
0°C to +70°C
________________________________________________________________________EV Kit
________________________________________________________________
Maxim Integrated Products
1
Call toll free 1-800-998-8800 for literature.
MAX555 Evaluation Kit
Evaluates: MAX555
____________________Component List
DESIGNATION
C1–C10, C14–C18,
C25, C26, C28
C19, C20
C21
C22
C23, C24
J1–J16
R1–R13, R20, R21
R14
R16
R17
R18
R19
U1
U2
U3
U4
QTY
18
2
1
1
2
16
15
1
1
1
1
1
1
1
1
1
DESCRIPTION
0.1µF ceramic capacitors
10µF tantalum capacitors,
surface-mount
22µF tantalum capacitor,
surface-mount
47µF tantalum capacitor,
surface-mount
0.01µF ceramic capacitors
SMA connectors
51Ω, 5% resistors
121Ω, 1% resistor
82.5Ω, 1% resistor
182Ω, 1% resistor
68.1Ω, 1% resistor
100Ω trim pot
MAX555CQK
LM337T
MX580KH
MAX410CPA
_______________Detailed Description
Digital Inputs
The MAX555 EV kit board has high-frequency SMA con-
nectors for the differential-clock and DAC data inputs.
Each of these inputs has on-board 50Ω pull-down resis-
tors to -2V. The -2V supply is regulated down from the
-5.2V power supply, as shown in Figure 1. The MAX555
is set-up in the clocked mode (BYPASS = logic 0) on the
EV kit board, with a 50Ω resistor (R13) connected to
-2V. Clocked-mode operation is recommended for all
high-speed applications. Removing R13 and connect-
ing the BYPASS pin of the MAX555 to ground will select
the transparent data mode, as described in the MAX555
data sheet.
DAC Outputs
The MAX555 has complementary voltage outputs, VOUT
and VOUT. Both have 50Ω output impedances and
must be terminated correctly to achieve the best perfor-
mance. Applications requiring a single-ended output
should use VOUT, since it is trimmed to higher accuracy
than VOUT. Both VOUT and VOUT should always be ter-
minated with 50Ω to ground for best performance. An
alternative way to achieve a single-ended output is to
drive a balun transformer with both VOUT and VOUT.
The balun connection will reduce the even-order har-
monics in the output.
_________________________Quick Start
1) Connect the power supply to the MAX555 EV kit.
The power-supply input pads are located along the
top edge of the board. The board requires a power
supply that provides +5V and -5.2V with a common
ground.
2) Connect 50Ω cables to the VOUT and VOUT out-
puts with proper terminations.
3) Connect a word generator to the data inputs
(D0–D11) and the clock inputs. All of these inputs
are 100k ECL compatible.
4) Turn on the power-supply and signal sources.
5) Observe the output waveforms on VOUT and VOUT.
Power Supplies
The EV kit board requires a -5.2V supply (at 425mA
nominal) for the DAC and 50Ω terminations, and a +5V
supply (at 12mA nominal) for the on-board reference
circuit, and ground.
DAC Reference Options
The MAX555 uses an external +1V reference, which is
supplied on the EV kit board using the circuit shown in
Figure 1. This reference voltage can be adjusted to dif-
ferent values between 1.2V and 0.4V using potentiometer
R19. The V
REF
value can be measured at the V
REF
pad.
The MAX555 will typically achieve its best spurious per-
formance with V
REF
values in the 0.6V to 0.8V range, as
described in the MAX555 data sheet. Experimentation
with different V
REF
values is recommended to maximize
the AC performance in your application.
2
_______________________________________________________________________________________
MAX555 Evaluation Kit
Evaluates: MAX555
J3
VREF
TEST POINT
JU2
+1VREF
J5
38 39
J6
54
58
J7
59
60
J8
62
64
65
J9
67
D4
6
J10
7
8
J11
J15
J12
J16
J13
26
J14
C6
0.1µF
C5
0.1µF
9
2
3
1
D3
D2
D1
D0 (LSB)
CLK
C27
OPEN
C2
0.1µF
C1
0.1µF
35
42
32
33 34
AVEE
-5.2V
J4
C3
0.1µF
5 55
DVEE
C4
0.1µF
VREF VREF/2 ROFFSET LOOPCRNT
D11 (MSB)
D10
D9
D8
D7
D6
D5
J1
17
VOUT
18
U1
MAX555
15
LGND
16
STAR GROUND
AT PIN 15
13
VOUT
ALTCOMPIB
14
J2
BYPASS
(HS)
44
ALTCOMPC
CLK
LBIAS
50
AGND
DGND
47
C7
0.1µF
-5.2V
28
C8
0.1µF
-5.2V
20 29 30 48 4 56 57 63 66
C9
0.1µF
C10
0.1µF
-5.2V
R1 R2 R3 R4 R5 R6 R7 R8 R9 R10 R11 R12
50Ω 50Ω 50Ω 50Ω 50Ω 50Ω 50Ω 50Ω 50Ω 50Ω 50Ω 50Ω
R20 R21
50Ω 50Ω
BYPASS
= ANALOG GROUND
= DIGITAL GROUND
R13
50Ω
-2V
C20
10µF
C14
0.1µF
C15
0.1µF
C16
0.1µF
C17
0.1µF
C18
0.1µF
C19
10µF
Figure 1. MAX555 EV Kit Schematic Diagram
_______________________________________________________________________________________
3
MAX555 Evaluation Kit
Evaluates: MAX555
-2V SUPPLY
-5.2V
+5V
REFERENCE CIRCUIT
C21
22µF
3
R14
121Ω
1%
2
IN
OUT
U2
LM337T
C23
0.01µF
+VS
U3
VOUT
MX580KH
GND
C24
0.01µF
R19
100Ω
R18
68.1Ω
1%
+5V
-2V
1
ADJ
R17
182Ω
1%
U4
2
C25
0.1µF
7
6
3
MAX410
4
+1VREF
C22
4.7µF
R16
82.5Ω
1%
C28
0.1µF
C26
0.1µF
-5.2V
Figure 1. MAX555 EV Kit Schematic Diagram (continued)
4
_______________________________________________________________________________________
MAX555 Evaluation Kit
Evaluates: MAX555
Figure 2. MAX555 EV Kit Component Placement Guide—
Component Side
Figure 3. MAX555 EV Kit Component Placement Guide—
Back Side
Figure 4. MAX555 EV Kit PC Board Layout—Component Side
Figure 5. MAX555 EV Kit PC Board Layout—Layer 2 (Ground
Layer)
_______________________________________________________________________________________
5
Plik z chomika:
Kot_Maciek
Inne pliki z tego folderu:
0001.PDF
(10 KB)
1003.PDF
(374 KB)
1002.PDF
(139 KB)
1004.PDF
(342 KB)
1005.PDF
(170 KB)
Inne foldery tego chomika:
PDF2
PDF3
SPICE
Zgłoś jeśli
naruszono regulamin