Magrav Power Schematics updated 10-31-15 v2.pdf

(5369 KB) Pobierz
MAGRAV Power Unit: Build and Grow
Keshe Foundation R&D Group
Lists of Items
1.) Gauge #14 Solid Copper Wire - about 20-30 meters to make 3 sets of MAGRAV COILS
2.) Nano Coating Kit (Refer to Videos of You Tube)
3.) Hand Drill with 2 rods for inner and outer coil forming
or 2 Screw Drivers with different rod diameter that can be inner and outer coils former
4.) Gans Mix for Coating the Coils and putting on the Center Gans Container
5.) Plasma Capacitor - 2-3 Units
6.) A lot of Patience, Prayers and Love in doing your MAGRAV Power Unit
Coils Specfications
1.)
All Coiled Counter Clockwise (use the Right Thumb Rule - by pointing your Right Thumb towards you
and curl your 4 fingers to the left going in your palm- The Curl is the Direction of Turn)
2.) Diameter of Loop Coils Varies on tubes use to make the coils.
3.) Magnetical Loop (Outer) consists of 2 coils Magnetical Coil (outer) and Gravitational Coil (inner)
- 140-160 Turns
4.)Gravitational Loop (Inner) consists of 2 coils Magnetical Coil (outer) and Gravitational Coi l(inner)
- 70-80 Turns
Steps
1.) Pray and Make the Coils- 3 sets.
2.) Nano-Coat the Coils using Standard Caustic Method and proper Drying.
3.) Coating the Coils with Gans Mix (Paste/Liquid) and Dry it properly.
4.) Assemble the Coils and Connect properly (make sure to fold the ends of the wires towards itself)
5.) Assemble the casing and properly arrange and stack all parts including the Gans Center Container
6.) Connect the Plasma Capacitor Properly.
7.) Check the Connections again (you can use electrical shrink tape to hold the connections)
8.) Install proper Switches or Breakers to the System
9.) Always consult an Electrical Engineer or Technician when connecting to the Main Power Line
10.) Build another one for your Neighbor and Relatives
MAGRAV Coil Circuit Connection
Keshe Foundation R&D Group
August 30, 2015
Magnetical Coil
(-)
(+)
Gravitational Coil
Extended Wire
from Gravitational Coisl
Gravitational Coil End
Magnetical Coil End
Magnetical Plasma Flow
Gravitational Plasma Flow
Gans Container
Specifications:
Gauge #14 Solid Copper Wire
All Coiled Counter Clockwise
Diameter of Loop Coils Varies on
tubes use to make the coils.
>
Magnetical Loop
(Outer) consists
of 2 coils Magnetical Coil (outer)
and Gravitational Coil (inner)
- 162 Turns
>
Gravitational Loop
(Inner) consists
of 2 coils Magnetical Coil (outer)
and Gravitational Coil - 81 Turns
MAGRAV Coil Circuit Stacked & connected in Series
Keshe Foundation R&D Group
August 30, 2015
(-)
Note:
1. Connecting wires must
be nano-coated.
2. Always twist the ends of
the wire back to itself.
(-)
(+)
(+)
3
Grav Loop =
(-)
(+)
2
2.5 cm
5 cm
(+)
1.0 to 1.5 cm
1
2.5 cm
(-)
Plasma Capacitor (Single Layer)
Keshe Foundation R&D Group
Ocotber 30, 2015 - Edited October 31, 2015
(+)
(-)
Nano Coated Copper Coil
Nano Coated Copper Wire
Fire Resistant Paper with Dried Gans
Insulating Tube
MAGRAV Power AC Grid Connection- Config 1
Keshe Foundation R&D Group
August 30, 2015
(-) (N)
(-) (N)
AC
Power
Grid
LOAD
(+) (L)
(+)
(-)
(+) (L)
Plasma Capacitor
3
Magnetical Coil
Gravitational Coil
Extended Wire
from Gravitational Coil
Gravitational Coil End
Magnetical Coil End

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika:

Zgłoś jeśli naruszono regulamin